<em id="b06jl"></em>
      <tfoot id="b06jl"></tfoot>
      <tt id="b06jl"></tt>

        1. <style id="b06jl"></style>

              狠狠干奇米,国产igao,亚卅AV,污污内射在线观看一区二区少妇,丝袜美腿亚洲综合,日日撸日日干,91色鬼,夜夜国自一区
              您好,歡迎來到易龍商務網!
              全國咨詢熱線:15057959687

              輥道設備高性價比的選擇「多圖」

              【廣告】

              發布時間:2020-07-19 20:07  






              特別是輸出輥道,過去多采用上述方法對中,但是近有把輥距縮小的傾向,因而采用后一種斜輥布置方式的輥道正在減少。這是為了在軋制薄規格的帶鋼時避免使帶鋼在輥道上因終軋速度高而造成折疊。此外,對于輥道的速度和輥子直徑也要充分考慮好。

              In particular, the output roller table used to use the above methods in the past, but recently there is a tendency to narrow the distance between rolls. Therefore, the roller table with the latter one is decreasing. to avoid folding the strip on a thin strip of strip to avoid the high finishing speed of the strip on the roller. In addition, the speed of the roller and the diameter of the roller should be fully cidered.


              為使鑄坯平穩迅速地運送,有時將這個區的輥道設計成可升降的。輥道按驅動方式可分為集中傳動輥道和單獨傳動輥道兩種。集中傳動輥道由一臺電機帶動一組輥子,通過電機一減速機一鏈輪傳動,或者通過電機一減速機~長軸一傘齒輪傳動方式傳動。



              In order to deliver the billet smoothly and quickly, the roller table in this area is sometimes designed to be lifted and lifted. The roller table can be divided into two types: the  drive roller and the separate drive roller. The  driven roller table is driven by a motor to a set of rollers, driven by a motor, a reducer or a sprocket, or through a motor, a reducer, a long shaft and a bevel gear transmission mode.


              單獨傳動輥道為一個電機帶動一個輥子。這種輥道結構簡單,操縱靈活,維修方便。根據鑄坯的斷面尺寸計算選擇輥子直徑和輥身長度,切割區后的輥道輥間距取決于定尺長度。為使軋件能夠在輥道中心運行,采用鼓形輥,并且交替地使左右兩邊的水平面稍微傾斜,或者使輥子的軸線與軋件運行方向的交角交替地比直角稍微偏斜一些。切割前輥道速度與拉坯速度一致,切割后要迅速輸送鑄坯,輥道速度一般為20~30m/min。

              A single drive roller is used as a motor to drive a roller. The roller table is simple in structure, flexible in operation and convenient in maintenance. According to the section size of the slab, the diameter of the roller and the length of the roller are calculated. The roller spacing after the cutting area depends on the length of the length. Before cutting roller speed and casting speed, after cutting to quickly transfer slab, roller speed is 20 ~ 30m/min.


              包膠滾筒的壽命是比較長的,像這種要求就是要壽命長的,因為包在滾筒上邊也不是很方便取下來呀,所以這就又驗證一點.

              The life of the rubber drum is long, and the requirement is long life, because it is not very convenient to take the package on the top of the drum, so this will verify the first point again.




              行業推薦
              主站蜘蛛池模板: 五月婷婷成人| 长垣县| 欧美综合激情网| 日韩欧美亚洲| 99国产精品永久免费视频| av中文无码韩国亚洲色偷偷| 欧美最猛性xxxxx大叫| 伊人99| 亚洲AV无码成人精品区网页 | 亚洲欧洲制服| 国产亚洲成人网| 自拍视频在线观看成人| 少妇高潮喷水在线观看| 偷拍精品一区二区三区| 亚洲人成人网站色www| 人人爽人人爽人人片av| 紫阳县| 精品无码国产一区二区三区51安| 免费在线3A级| 亚洲国产成人一区二区三区| 九九免费成年人在线观看| 国产男女猛烈无遮挡免费视频| 久久国产一区二区日韩av| 久久国内精品自在自线91| 日韩国产欧美精品在线| 亚洲中文字幕无码爆乳av| 内射视频福利在线观看| 女人18毛片水真多| 亚洲精品国产av一区二区| 亚洲色大成网站www永久男同| 超碰99在线| 国产97色在线 | 免费| 色中色AV| 久久久久久亚洲精品a片成人| 亚洲AV无码久久精品色欲| 俺来也www久久婷婷| 91资源站| 久久精人人妻一区二区三区| 亚洲国产精品久久久天堂麻豆宅男 | 九九三级影视| 国产欧美精品久久久|